Chamberlain Travel Limit and Force Adjustment (Video)

Programming the Travel on a Chamberlain Garage Door Opener with a Yellow Learn Button

Congratulations on owning a Chamberlain Garage Door Opener! This is a top-quality device that guarantees you years of reliable service. This guide will help you to program the travel on your Chamberlain garage door opener with a yellow learn button. The programming process is fairly simple and can be done in just a few steps. Let’s get started!

Before You Start

Safety First

Before you start with the programming, ensure that you have taken all necessary safety precautions. Make sure that there are no obstructions in the path of the garage door and that it is in good working condition. If there are any loose screws or bolts, tighten them first. Also, make sure that the garage door is fully closed before you begin the programming process.

Gather Necessary Tools

For this programming task, you won’t need any special tools. Just make sure that you have your garage door opener remote control handy.

Steps to Program the Travel on Your Chamberlain Garage Door Opener

Locate Adjustment Button on Chamberlain Garage Door Opener

Locate the Adjustment Buttons

Find the Adjustment Button and the up and down arrow buttons on the side or back panel of your garage door opener. TIP: Both UP and DOWN buttons can be used to move the door as needed.

Locate the Adjustment Buttons on a Chamberlain Garage Door Opener

Set the OPEN Position

  1. Press and hold the Adjustment Button until the UP Button begins to flash and/or a beep is heard. This indicates the opener is ready to set the OPEN position.
  2. Press and hold the appropriate arrow until the door is in the desired UP position.
  3. Once the door is in the desired UP position, press and release the Adjustment Button.
  4. The garage door opener lights will flash twice, and the DOWN Button will begin to flash. This locks in the OPEN position and indicates the opener is ready to set the CLOSED position.

Set the CLOSED Position

  1. Press and hold the appropriate arrow until the door is in the desired DOWN position.
  2. Once the door is in the desired DOWN position, press and release the Adjustment Button.
  3. The garage door opener lights will flash twice, and the UP Button will begin to flash. This locks in the CLOSED position and sets the opener into force programming mode.
  4. Press and release the UP Button. When the door travels to the programmed UP position, the DOWN Button will begin to flash.
  5. Press and release the DOWN Button. The door will travel to the programmed DOWN position, and programming is complete.

Troubleshooting

Lights Flashing 5 Times

If the garage door opener lights are flashing 5 times during the steps to Program the Travel on a myQ Enabled Garage Door Opener, the programming has timed out.

Lights Flashing 10 Times

If the garage door opener lights are flashing 10 times during the steps to Program the Travel on a myQ Enabled Garage Door Opener, the safety reversing sensors are misaligned or obstructed.

Align and Unblock Sensors

When the sensors are aligned and unobstructed, cycle the door through a complete up and down cycle using the remote control or the UP and DOWN buttons on the operator.

Repeat Steps if Necessary

If you are unable to operate the garage door UP and DOWN, repeat these steps to Program the Travel on a myQ Enabled Garage Door Opener.

NOTE: For garage door openers manufactured after 2022, verify the LEDs on the safety sensors are on; the lights on the GDO will not blink 10 times.

Safety Reversal System Test

After you do ANY adjustments, the safety reversal system MUST be tested. With the door fully open, place a one-inch board (or a 2×4 laid flat) on the floor, centered under the garage door. Operate the door in the down direction. The door must reverse when striking the obstruction.

Conclusion

Programming the travel on your Chamberlain garage door opener with a yellow learn button is a simple process that can be done in a few minutes. By following the steps mentioned above, you can easily program the travel limits on your garage door opener and ensure its proper operation.

Remember to test the garage door opener after programming the travel limits to make sure it is working correctly. Regular maintenance of your garage door and opener is also essential to ensure its long-lasting performance. If you face any issues or need professional assistance, do not hesitate to contact a qualified technician or Chamberlain customer support. If you live in OKC or surrounding areas feel free to contact Good Guys Garage Door Repair OKC

Leave a Comment